Intel MultiProcessor Specification v1.1
    Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
Processor #0 Pentium(tm) APIC version 17
Processor #1 Pentium(tm) APIC version 17
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 2
Console: colour *CGA 80x25, 1 virtual console (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fafa0
pcibios_init : BIOS32 Service Directory entry at 0xfb480
pcibios_init : PCI BIOS revision 2.10 entry at 0xfb4b0
Probing PCI hardware.
Calibrating delay loop.. ok - 52.84 BogoMIPS
Memory: 30236k/32768k available (704k kernel code, 384k reserved, 1444k data)
This processor honours the WP bit even when in supervisor mode. Good.
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.12 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized

Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.10 (root@trumpf-9.rz.uni-mannheim.de) (gcc version 2.7.2) #2 Fri Aug 2 14:18:47 MET DST 1996
Booting processor 1 stack 00002000: Calibrating delay loop.. ok - 53.04 BogoMIPS
Total of 2 processors activated (105.88 BogoMIPS).
Floppy drive(s): fd0 is 1.44M
Started kswapd v 1.4.2.2 
FDC 0 is a post-1991 82077
scsi-ncr53c7,8xx : at PCI bus 0, device 12,  function 0
scsi-ncr53c7,8xx : warning : revision of 17 is greater than 2.
scsi-ncr53c7,8xx : NCR53c810 at memory 0xfbfbe000, io 0xe400, irq 11
scsi0 : burst length 8
scsi0 : NCR code relocated to 0x84600 (virt 0x00084600)
scsi0 : test 1 started
scsi0 : NCR53c{7,8}xx (rel 17)
scsi : 1 host.
scsi0 : target 0 accepting asynchronous SCSI
scsi0 : setting target 0 to asynchronous SCSI
  Vendor: MAXTOR    Model: MXT-1240S         Rev: I1.5
  Type:   Direct-Access                      ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi0 : target 2 accepting asynchronous SCSI
scsi0 : setting target 2 to asynchronous SCSI
  Vendor: PLEXTOR   Model: CD-ROM PX-6XCS    Rev: 2.05
  Type:   CD-ROM                             ANSI SCSI revision: 02
Detected scsi CD-ROM sr0 at scsi0, channel 0, id 2, lun 0
scsi : detected 1 SCSI cdrom 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 2423457 [1183 MB] [1.2 GB]
tulip.c:v0.10 8/11/95 becker@cesdis.gsfc.nasa.gov
        +0.72 4/17/96 http://www.dsl.tutics.tut.ac.jp/~linux/tulip
eth0: smc8432 (DEC 21041 Tulip) at 0xe800, 00:00:c0:55:6b:d3, IRQ 10
arcnet.c: v2.54 96/07/05 Avery Pennarun 
  arc0: Stage 1: No ARCnet cards found.
Partition check:
 sda: sda1 < sda5 sda6 sda7 > sda2
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 52300k swap-space
Max size:327021   Log zone size:2048
First datazone:42   Root inode number 86016